Hitachi Typhoon 4x- 5x- 7.7 Files Descargar Drivers

Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Dos driver, AutoCAD (PostScript)
Tamaño
230Kb
Nombre del archivo
3332461a.exe
Información
CONTENTS

1. INTRODUCTION
2. INSTALL THE DRIVER FILE
3. CONFIGURE AUTOCAD
4. PRINTER SETTINGS
5. SHADING or GRAYSCALES
6. LINETYPES or LINEWIDTHS
7. PLOT FROM AUTOCAD
8. STOPPING THE PLOT
9. SPOOLING
10. USE PLOT-TO-FILE TO PLOT TO A PORT

1. INTRODUCTION

This document explains the installation and use of the Autodesk Device
Interface (ADI) plotter driver for Dataproducts printers. This driver
supports the printers and AutoCAD versions listed above. AutoCAD drivers
are available for additional Dataproducts printers that are not listed
above. Contact Dataproducts or your driver supplier to get the correct
driver and installation instructions for your printer.

This driver is a "protected-mode" ADI plotter driver. ADI is an acronym
for the Autodesk Device Interface, with describes the specification that
was used to create this driver. Along with these instructions, please
consult your AutoCAD Installation and Performance Guide concerning plotting
with protected mode ADI devices, your AutoCAD Users Guide section on
plotting, and your printer user's manual.

This driver is a product of and is supported by Dataproducts Corporation,
not by Autodesk.

To use the driver, do the following:

1. INSTALL THE DRIVER FILE
2. CONFIGURE AUTOCAD
3. PLOT FROM AUTOCAD

Details for each of these steps are given below. The procedures differ
depending on what release of AutoCAD you are using. Follow only the steps
under the headings for your release of AutoCAD.

2. INSTALL THE DRIVER FILE

Your distribution disk or directory contains one or more driver files.
Different driver files work with different operating systems and different
AutoCAD releases. You must copy the correct driver file to the proper
AutoCAD directory and filename on your hard disk.

Follow the instructions in the installation section below that is labeled
for your release of AutoCAD. Afterwards, continue with the section labeled
CONFIGURE AUTOCAD. Installation sections are available for the following
AutoCAD Releases:

Section AutoCAD Release driver file

2.1 Release 13 for DOS pldptyph.exp
2.2 Release 13 for Windows pldpty13.dll
2.3 Release 12 for DOS pldptyph.exp
2.4 Release 12 for Windows pdlptyph.dll
2.5 Release 12 for Sparc (SunOS 4.1.x) pldpty.unx
2.6 Release 12 for Solaris pldpty.sol
2.7 Releases 10 & 11 for DOS pldptyph.exp
2.1 Release 13 for DOS
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Dos driver, Word 5.5/6.0 (PostScript)
Tamaño
108Kb
Nombre del archivo
3332461d.exe
Información
INSTALLATION INSTRUCTIONS FOR MICROSOFT WORD 5.5 and 6.0 FOR DOS
DRIVERS
*****************************************************************
1. Copy the required driver to a directory on your PC. The
following method is recommended.

ACTION COMMENTS
cd \word Change to Word working directory
copy a:\word\*.* Copy driver files to Word directory

The example above assumes that Microsoft Word is installed in the
directory \word on drive C:, and the installation diskette is in
drive A:.

2. Run Microsoft Word.
3. Select the File/Printer Setup menu item.
4. Select the Word directory.
5. Click on the Files box to list PRD files (i.e. driver files)
6. Click on the PRD file and a list of Dataproducts printers will
appear in the Printer Name box.
7. Select the required model, change settings such as Connect To
(port) or Graphic Resolution if required, and click OK. The
printer driver is now loaded.
SELECTING PAPER SOURCE IN MICROSOFT WORD
-----------------------------------------
You can select a paper feed source in File/Print or File/Printer
Setup dialogues. The following choices are available for
Dataproducts Typhoon printers:
1. Typhoon 30 Simplex model - Continuous, Bin 1, Envelope.
Continuous - uses default printer hopper (set on printer's
control panel)
Bin 1 - uses Hopper 6
Bin 2 - uses Hopper 5
Mixed - first page from Bin 1, the rest from Bin 2
Envelope - uses Hopper 4

2. Typhoon 30 Duplex model - Continuous, Bin 1, Bin 2, Bin 3,
Mixed, Envelope.
Continuous - uses default printer hopper (set on printer's
control panel)
Bin 1 - uses Hopper 1
Bin 2 - uses Hopper 2
Bin 3 - uses Hopper 3
Mixed - first page from Bin 1, the rest from Bin 2
Envelope - uses Hopper 4

3. Typhoon 60 model - Continous, Bin 1, Bin 2, Bin 3, Mixed, Envelope.

Continuous - uses default printer hopper (set on printer's control
panel)
Bin 1 - uses Hopper 1
Bin 2 - uses Hopper 2
Bin 3 - uses Hopper 3
Mixed - The first page prints from Bin 1, the rest from Bin 2
Envelope - uses Hopper 4

*******************************************************************************
Limitations: Word 5.5 / 6.0 Postscript
*******************************************************************************
1. When using the Typhoon 30 or 60 Postscript driver in Word 5.5 or 6.0 you need
to select the appropriate Hopper (I.E. Hopper 1, Hopper 2, Hopper 3, Hopper 4)
for the paper size of the job you are sending. If you send the wrong page size
to a certain Hopper the job will print on the page from that Hopper no matter
what its size is.

*******************************************************************************
Limitations: Word 5.5 / 6.0 PCL5
*******************************************************************************

1. The Perfect Words Virtual Font Cartridge is not supported by
the WORD 5.5/6.0 driver
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Dos driver, WordPerfect 5.1 (PostScript)
Tamaño
116Kb
Nombre del archivo
3332461e.exe
Información
INSTALLATION INSTRUCTIONS FOR WORDPERFECT 5.1 FOR DOS DRIVER
*****************************************************************

1. Copy the required driver to a directory on your PC. The following
method is recommended.

ACTION COMMENTS
cd \wp51 Change to WordPerfect directory
copy a:\wp51\*.* Copy the required driver files
t3060_51 De-compress the self extracting file

The example above assumes that WordPerfect is installed in
directory \wp51, and the installation diskette is in drive A:.

** The keystrokes mentioned below are for Word Perfect 5.1
for DOS only.

2. Run WordPerfect.
3. Select the Print Menu(SHIFT F7).
4. Choose Select Printer option (S).
5. Choose Additional Printers (2 or A).
6. Select Printer you are using and correct emulation from the list of available
printer drivers by scrolling down the list with the arrow keys then entering
(1 or S) to confirm your selection.
7. Press Enter to confirm filename
8. Exit Help Screen (F7).
9. Scroll cursor bar to appropriate printer driver.
10. Type S to confirm selection. The printer driver is now
loaded.

************************************************************************
README FILE FOR DATAPRODUCTS TYPHOON 30,40, AND 60 DOS DRIVERS
12/3/95 P/N 333246-001
************************************************************************

Copyright (c) 1992-1995 Dataproducts Corporation. All Rights Reserved.

This file lists the files used for WordPerfect v.5.1 DOS drivers.

** Note *****************************************************************
For Typhoon 40 Driver in all applications select Typhoon 30 in Duplex mode
Stacker 7 is optional for Typhoon 40
*************************************************************************

\WP51
README.TXT Driver installation instructions for WordPerfect 5.1.
T3060_51.EXE Self-Extracting file containing the following files

T360_51.ALL WordPerfect 5.1 driver (PCL5)
T360PS51.ALL WordPerfect 5.1 driver (PostScript)
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Dos driver, WordPerfect 6.0 (PostScript)
Tamaño
111Kb
Nombre del archivo
3332461f.exe
Información
INSTALLATION INSTRUCTIONS FOR WORDPERFECT 6.0 FOR DOS DRIVER
*****************************************************************

1. Copy the required driver to a directory on your PC. The follow
method is recommended.

ACTION COMMENTS
cd \wpc60dos Change to WordPerfect driver directory
copy a:\wp60\*.* Copy the required driver files
t3060_60 De-compress the self extracting file
The example above assumes that WordPerfect uses directory
\wpc60dos (default) to search for driver files, and the
installation diskette is in drive A:.

** The keystrokes mentioned below are for Word Perfect 6.0
for DOS only.

2. Run WordPerfect.
3. Select File/Print (SHIFT F7).
4. Choose Select Printer option (S).
5. Choose Add Printers (2 or A).
6. Select the appropriate printer driver from the list of available printer
drivers by scrolling down the list with the arrow keys then entering (1 or S)
to confirm your selection.
7. Click OK to confirm filename
8. Click Close to exit information screen.
9. Edit settings such as Port if needed and click OK.
10. Scroll cursor bar to the driver which you are using.
11. Type 1 or S to confirm selection. The printer driver is now
loaded.

************************************************************************
README FILE FOR DATAPRODUCTS TYPHOON 30,40, AND 60 DOS DRIVERS
12/3/95 P/N 333246-001
************************************************************************

Copyright (c) 1992-1995 Dataproducts Corporation. All Rights Reserved.

This file lists the files used for WordPerfect 6.0 for DOS drivers.

** Note *****************************************************************
For Typhoon 40 Driver in all applications select Typhoon 30 in Duplex mode
Stacker 7 is optional for Typhoon 40
*************************************************************************

\WP60
README.TXT Driver installation instructions for WordPerfect 6.0.
T3060_60.EXE Self-Extracting file containing the following files

T360_60.ALL WordPerfect 6.0 driver (PCL5)
T360PS60.ALL WordPerfect 6.0 driver (PostScript)
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Macintosh Utilities and PPDs
Versión Driver
464Kb
Tamaño
464Kb
Nombre del archivo
mac-utility-typhoon.sea
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows 3.1 PCL5
Tamaño
362Kb
Nombre del archivo
333245_1.exe
Información
CONTENTS OF THIS DISK *
*************************
- readme.txt This file
- typhoon.drv Windows 3.1 Driver Typhoon 30/40/60 PCL5
- finstall.dll Font installer program
- finstall.hlp Font installer help file
- unidrv.dll File accompanying driver
- unidrv.hlp Universal driver help file
- typhoon.hlp Driver help file
- oemsetup.inf File to enable installation of driver

***************************************************************************
* INSTALLATION INSTRUCTIONS FOR Typhoon 30/40/60 PCL5 Windows 3.1 Drivers *
***************************************************************************
To install the DPC Typhoon 30/40/60 PCL5 Printer Driver:

1. Start Windows 3.1.

2. Choose Control Panel from the Main Group in Program Manager.
The Control Panel window appears.

3. Choose the Printers icon from the Control Panel window.
The Printers dialog box appears.

4. Choose the Add >> button.

5. From the List of Printers: dialog box, select the Install Unlisted
or Updated Printer.

6. Choose Install.

7. Insert the driver diskette

8. Enter the drive letter of the drive containing the driver diskette.

9. Choose OK.

10. Highlight the appropriate driver for your printer and click
OK. Windows may request that you insert one of the Windows Installation
disks, if so, follow the instructions on the screen.

11. The printer driver defaults to LPT1. To change the connection
select the Connect button.

13. Select Typhoon 30 PCL5 or Typhoon 40 PCL5 or Typhoon 60 PCL5 in Installed
Printers list box and click Set as Default Printer button.

14. Use Setup, Options, and Fonts selections to verify the required printer
driver configuration.

15. Click the Close button.

The Typhoon 30/40/60 PCL5 printer driver is now installed. If you have
any difficulties, refer to the Windows 3.1 User's Guide Chapter 6, Print
Manager for information about installing printer drivers.

***********************************
* TECHNICAL NOTES AND LIMITATIONS *
***********************************
1. When printing with resident fonts accurate 6 lpi spacing is not preserved.

2. In Microsoft Word 2.0 for Windows 3.1 6pt letter gothic text cannot be
selected from the list of point sizes, instead the information must be
typed in as 4pt and it will print correctly.

3. The width of the Output Bin Box in the Options window is not large enough
to accommodate Cascade 1,2,3,4 combination in the Typhoon 60 PCL5 driver.

4. Printing at 150 & 75 DPI resolutions may cause some loss of image for paper
sizes: Ledger, A3, A4, B4, B5.

5. When printing to a file from some applications VFC fonts may be substituted
with resident fonts and VFC fonts become unavailable.
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows 3.1 PostScript
Tamaño
251Kb
Nombre del archivo
333244_1.exe
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows 95 PCL5
Tamaño
312Kb
Nombre del archivo
333243_1.exe
Información
CONTENTS OF THIS DISK *
*************************
- readme.txt This file
- typhoon.drv Windows 95 Driver for Typhoon 30/40/60 PCL5.
- finstall.dll Font installer program.
- finstall.hlp Font installer help file.
- unidrv.dll File accompanying driver.
- unidrv.hlp Help file accompanying driver.
- dpcpcl5.inf Windows printer installation setup file.
- iconlib.dll Dynamic Link Library for printer icons.
- pjlmon.dll PJL language monitor.

**************************************************************************
* INSTALLATION INSTRUCTIONS FOR TYPHOON 30/40/60 PCL5 Windows 95 DRIVERS *
**************************************************************************
To install the DPC Typhoon 30/40/60 printer default resolution Printer
drivers:

1. Start Windows 95.

2. Insert the Dataproducts driver disk into drive a: or b:.

3. Open the "My Computer" group.

4. Open the "Printers" folder and select "Add Printers".
The "Add Printers Wizard" appears.

5. Proceed though the series of windows presented by the "Add Printers
Wizard" - selecting the "Have Disk" button when prompted for the
type of printer to install.

6. Enter the letter of the drive containing the driver disk (from step 2).

7. Select the printer model to install.

8. Continue through the "Add Printers Wizard" until the installation is
complete.

NOTE: If you installs Windows 95 over Windows 3.x and you had
the same Dataproducts printer model installed in 3.x as you
are trying to install in 95, a message may appear after step 7
above informing you that a driver is already installed for this
printer. Choose "Replace existing driver" option (Windows 3.x
PCL5 drivers are not compatible with Windows 95). Once
installation is complete, delete the "Dataproducts
Typhoon (copy 2)" icon in the "Printers" group.

***********************************
* TECHNICAL NOTES AND LIMITATIONS *
***********************************
1. When printing with resident fonts accurate 6 lpi spacing is not preserved.

2. In Microsoft Word 2.0 6pt letter gothic text cannot be selected from
the list of point sizes, instead the information must be typed in as 4pt
and it will print correctly.

3. Printing at 150 & 75 DPI resolutions may cause some loss of image for all
paper sizes.

4. When printing to a file from some applications VFC fonts may be substituted
with resident fonts and VFC fonts become unavailable.

5. Choosing Vector Graphics increase the speed of printing, but in some cases
like overlays may cause data loss of image. If this problem occurs, switch
to Raster Graphics.

6. Changing margin settings in the Paper\Unprintable Area causes loss of image
if Vector Graphics is selected.

7. Restore Defaults in Details\Spool Settings does not effect bi-directional
settings.
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows NT 3.5.1 PCL
Tamaño
153Kb
Nombre del archivo
333239_1.exe
Información
CONTENTS OF THIS DISK *
*************************
- readme.txt This file.
- typhoon.dll Typhoon 30/40/60 PCL5 Minidriver DLL Version 2.31.
- rasdd.dll Windows NT PCL5 Unidriver.
- rasddui.dll Windows NT PCL5 Unidriver.
- rasddui.hlp Windows NT PCL5 Unidriver help file.
- printer.inf Installation setup file.
***************************************************************************
* INSTALLATION INSTRUCTIONS FOR Typhoon 30/40/60 PCL5 Windows 3.1 Drivers *
***************************************************************************

You need to follow the following procedure to install any of the Dataproducts
Typhoon 30/40/60 PCL5 Printer drivers included with this disk:

1. After logging in, execute "PRINT MANAGER" from the "MAIN" program group.

2. Select "Printer" and choose "Create Printer..." from the menu bar.

3. Type in a unique name in the "Printer Name" box and select "Other" in the
"Driver" box. (This option is at the end of the list of printer names.)

4. At the "Install Driver" prompt window, type in the letter of the floppy
disk drive containing the Typhoon 30/40/60 Windows NT 3.5 drivers diskette
(A:\ or B:\) and click "OK".

5. At this point a list of printer drivers included on this disk appears in
the "Select Driver" window. Select the printer model by highlighting
the printer name, and click "OK". Wait while the appropriate files
are copied onto you system. When you are back in the Create Printer
dialog box, click "OK".

6. By now you should see a window titled "Printer Setup". In this window you can
configure various features including Printer memory, Font substitution,
Halftone and assign different paper sizes to different paper trays installed
in the printer.

7. After closing Printer Setup and Printer Properties windows, select
the appropriate printer in the "Default" box.
***********************************
* TECHNICAL NOTES AND LIMITATIONS *
***********************************

1. When printing with resident fonts accurate 6 lpi spacing is not preserved.

2. In Microsoft Word 2.0 for Windows 6pt letter gothic text cannot be
selected from the list of point sizes, instead the information must be
typed in as 4pt and it will print correctly.

3. Printing at 150 & 75 DPI resolutions may cause some loss of image for paper
sizes: Ledger, A3, A4, B4, B5.

4. When printing to a file from some applications VFC fonts may be substituted
with resident fonts and VFC fonts become unavailable.

5. RASTER PRINTER FONT INSTALLER does not recognize some soft fonts or
does not recognize them properly.

6. Microsoft Word v6.0a might causes small line to print in lower left hand
corner in Landscape orientation.

7. Changing PCL Upper Tray mapping via OCP does not have any effect
on the driver functionality, because the driver uses physical hopper
numbers for paper source selection.
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows NT 3.5.1 PostScript
Tamaño
250Kb
Nombre del archivo
399006_3.exe
Información
DISKETTE CONTENTS
=================

README.TXT This file
PRINTER.INF Installation setup file
T30PS.DLL Typhoon 30/40/60 Windows NT PostScript driver
T30PSUI.DLL Typhoon 30/40/60 Windows NT PostScript driver
PSCRIPT.HLP Windows NT PostScript driver help file
PSCRIPTX.HLP Windows NT PostScript driver help file
T30V4.PPD Typhoon 30 PostScript Printer Description file
T40V4.PPD Typhoon 40 PostScript Printer Description file
T60V4.PPD Typhoon 60 PostScript Printer Description file

****************************************
* FIRST TIME INSTALLATION INSTRUCTIONS *
****************************************
You need to follow the following procedure to install any of the drivers
included with this disk:

1. After logging in, execute "PRINT MANAGER" from the "MAIN" program group.

2. Select "Printer" and choose "Create Printer..." from the menu bar.

3. Type in a unique name in the "Printer Name" box and select "Other" for
"Driver". (This option is at the end of the list of printer names.)

4. At the "Install Drive" prompt window, type in the letter of the floppy
disk drive containing the driver disk (A:\ or B:\) and click the mouse
on "OK".

5. At this point a list of printer drivers included on this disk appears in
the "Select Drive" window. Using the mouse, select the printer model by
highlighting the printer name, and click on "OK".
Wait while the appropriate files are copied onto you system.
Change your printer port if necessary and click "OK".

6. By now you should see a window titled "PostScript Printer Setup".
In this window you can configure various features including
Font substitution, Halftone and assign different paper sizes to
different paper trays installed in the printer.
USER SUGGESTIONS
================
Typhoon 30/40/60 work fine by setting: Printer property/Settings/Timeout = 45
************************************************
* NOT THE FIRST TIME INSTALLATION INSTRUCTIONS *
************************************************
If you already have installed the driver and need to reinstall it again,
the following is the procedure you need to follow, in order to un-install
the driver:

1. Select the "FILE" command in the PROGRAM MANAGER. Select the "RUN"
option, and type "C:\WINNT\SYSTEM32\REGEDIT32.EXE". (If for some reason
the directory and drive letter of where NT files are stored at is
different, replace the C:\WINNT with the correct drive letter and
directory)

2. Select the window titled "HKEY_LOCAL_MACHINE on Local Machine".
Double click on "SYSTEM"
Double click on "ControlSet001"
Double click on "Control"
Double click on "Print"
Double click on "Environments"
Double click on "Windows NT x86"
Double click on "Drivers"
Compañía
Hitachi
Dispositivo
Impresoras y Plotters
Modelo
Hitachi Typhoon 4x- 5x- 7.7 Files
Descripción
Drivers
Sistema Operativo
Windows PostScript
Tamaño
301Kb
Nombre del archivo
333242-1.exe
Información
Diskette Contents
===========================================================================
README.TXT This file.
DPTYPHSP.INF Windows printer installation setup file.

T30V4.PPD PostScript Printer Description file (PPD) for Typhoon 30.
DPC Version 4.2W2.0.03.102495 (Version 4)

T40V4.PPD PostScript Printer Description file (PPD) for Typhoon 40.
DPC Version 4.2W1.0.02.102495 (Version 4)

T60V4.PPD PostScript Printer Description file (PPD) for Typhoon 60.
DPC Version 4.2W2.0.03.102495 (Version 4)

LDO.PFM PS font metric file for ITC-Lubalin-Graph-Demi-Oblique
LBO.PFM PS font metric file for ITC-Lubalin-Graph-Book-Oblique
LD.PFM PS font metric file for ITC-Lubalin-Graph-Demi
LB.PFM PS font metric file for ITC-Lubalin-Graph-Book
SD.PFM PS font metric file for ITC-Souvenir-Demi
SDI.PFM PS font metric file for ITC-Souvenir-Demi-Italic
SL.PFM PS font metric file for ITC-Souvenir-Light
SLI.PFM PS font metric file for ITC-Souvenir-Light-Italic

FONTS.MFM PostScript font metric data file.
ICONLIB.DLL Dynamic Link Library for printer icons.
PSCRIPT.DRV Driver file for Windows 95.
PSCRIPT.HLP Online help file.
PSMON.DLL Dynamic Link Library support file for driver.
TESTPS.TXT PostScript file for determining printer communication.
settings.

===========================================================================
Installation Instructions
===========================================================================
1. Start Windows 95.

2. Insert the Dataproducts driver disk into drive a: or b:.

3. Open the "My Computer" group.

4. Open the "Printers" folder and select "Add Printers".
The "Add Printers Wizard" appears.

5. Proceed through the series of windows presented by the "Add Printers
Wizard" - selecting the "Have Disk" button when prompted for the
type of printer to install.

6. Enter the letter of the drive containing the driver disk (from step 2).

7. Select the printer model to install.

8. Continue through the "Add Printers Wizard" until the installation is
complete.

NOTE: If you installed Windows 95 over Windows 3.x and you had
the same Dataproducts printer model installed in 3.x as you
are trying to install in 95, a message may appear after step 7
above informing you that a driver is already installed for this
printer. At this point you can choose to keep the existing driver
or to replace it. Select replace and continue through the
installation process. Once installation is complete, delete
the "Dataproducts Typhoon (copy 2)" icon in the "Printers" group.
Disponibles 11 archivos para Typhoon 4x- 5x- 7.7 Files
HelpDrivers Desde Marzo del 2000